title.jpg (17697 bytes)

CUTTING AND BENDING TOOL

@
YYT- 3

p15-1b.jpg (32424 bytes)

p15-2s.jpg (10705 bytes) p15-3s.jpg (9305 bytes)
INSTRUCTIONS FOR USE
p15-4s.jpg (6859 bytes) p15-5s.jpg (9035 bytes) p15-6s.jpg (16165 bytes) p15-7s.jpg (4284 bytes)
1
For the best cutting and bending results the components must be well tightened to the printed circuit board. It is advisable that the printed circuit boards are placed in a printed circuit board holder equipped with foam pressing cover
2
Lay the grooved tip of the fix knife on the P.C.B. and hook the lead. Keep the TP adprox. 200 raking.
Press the handles: the mobile knife springs out and simultaneously chops and bends the wires.
3
The TP/allows a working field of about 900. therefore if the copper strips are narrow or close together, it is advisable to move the TP/following them on the P.C.B.
4
At the end of the cutting and bending, the components are well-fixed on the printed circuit board with the leads evenly cut and bent at 900. Furthermore the scrubbing action of the TP allows an easier and quicker soldering of the components.
YYT3 TYPE
PLASTIC BODY TYPE
Suitable for cutting and bending component leads with no adjustment from 0.3mm to 1.0mm wire dia.

LEADS ARE CUT AND BENT 900 ACCORDING TO MIL-STANDARD

- YYT3 Poliamide and glass fiber casting body in a pleasant shape extremely strong; light to handle; wear-re-sistent and self lubricating.
- The cutting and bending heads, in special steel, are easily removed for changing or sharpening.
- The leads are evenly cut at constant length and bent at 900 (according to MIL norms) and left clean and ready for soldering.



CABLE-STRIPPER

YYT- 2
  • EXCLUSIVELY PRODUCE IN TAIWAN WITH TECHNICALITY SUPPLIED AND LICENSED BY ELCONTROL S.P.A. - ITALY

  • ATENT UNDER APPLICATION


p16-1b.jpg (24713 bytes)
@
p16-2s.jpg (8243 bytes)
INSTRUCTIONS FOR USE
p16-3s.jpg (7316 bytes) p16-4s.jpg (7353 bytes) p16-5s.jpg (6887 bytes) p16-6s.jpg (7732 bytes)
To obtain the circular incision in the insulation press lightly on the handles until the blades (1) come into contact then turn in a circular direction first ene way then the other until all the circumference is incised. Should a central piece of insulation need to be stripped, two incision must be made to mark the length to be stripped. Place the piece of insulation to be stripped in the special groove (2) on the side of the strippers. Press handles completely until blades (3) penetrate the insulation. Repeat this action until the desired length of insulation is stripped. Keep the handles depressed and turn the stripper slightly and draw away sideways so that the insulation comes clear.
YYT2 TYPE
Strip without regulation, cables of 6 of 18mm diameter (6 to 120 sq mm section)

SPARE KNIVES
CCF-Frontal knives set
CCL-Side knives set
IT CAN REMOVE THE INSULATION OF THE CABLE IN ANY POSITION AND FOR ANY REQUIRED LENGTH

- Strongly made in pressed steel and oven fired.
- Steel blades tempered for the circular incision and the lengthway cut. Can easily be removed for sharpening or substitution.
- The specially designed shape allows for any length to be stripped from the end or at any point of the cable.


bar-012.gif (4497 bytes)

butten.jpg (11822 bytes)
@
YU-YUAN MACHINERY INDUSTRIAL CO., LTD.
No. 9. Ta Tung St, Tu Cheng Industrial Zone Taipei Hsien, Taiwan, R.O.C.
Tel : 886-2-2268-2843  2268-7086~88     Fax : 886-2-2268-6330
E-mail : yuyuan@yu-yuan.com.tw